Plumbing Essentials: An Essential for When Installing a Bathtub
Plumbing Essentials: An Essential for When Installing a Bathtub
Blog Article
We have stumbled on this post pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the web and believe it made perfect sense to talk about it with you here.
Setting up a tub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a new one is additionally a moderately hard job. If the old bathtub is conveniently accessible, the task can relocate rapidly; if you need to open up a wall surface to eliminate the old tub as well as place the new tub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to move out the old tub and set in the new one. See to it you have certified on your own for the work and are comfortable trying it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to think about using one prior to you begin. Possibilities are you might require a specialist plumber to make tube connections.
This article will certainly assist you install a new bathtub in your shower room if you have actually currently purchased a brand-new bathtub and do not need to transform the plan of your previous water pipes.
Your tools and product checklist must comprise the following:
Preparing for the Setup
First of all, the sustaining frame supplied with the bath ought to be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop stress on the bath tub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its final position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, switch on the taps to drain any water staying in the system. The process of removing the existing taps can be fairly problematic due to the restricted accessibility that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly originate from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Before moving on to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, put the bathtub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the tub till the level reviews level.
To install faucets, fit all-time low of the furthest adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the supply of water as well as inspect all joints and also new pipework for leaks as well as tighten them if needed. Fill up the bathtub and additionally check the overflow electrical outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the producer's user's manual. Tiling as well as sealing around the tub must wait till the bathtub has actually been used at the very least once as this will resolve it into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washers remain in area in between the faucet and also the sink. Safeguard the faucet in position with the producer supplied backnut. As soon as the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The former type should be linked to the tap ends initially, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to crack a rigid seal, causing the water to penetrate the wall surface between the bath and the tiling, resulting in problems with wetness and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bathtub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can break relatively very early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the market. It is suggested to fit the floor tiles using waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that post about Tools You Need to Install a New Bathtub while doing a search on the web. So long as you enjoyed reading our blog posting please remember to share it. Thank you for taking the time to read it.
Plumbing care available. Report this page